1. Carrier Comfort Zone Problems
2. Carrier Comfort Zone Ii Installation Manual

Feb 09, 2018  Carrier Comfort Zone 1 Manual online manual for free. Get the best deals on Carrier Thermostats when you shop the largest online selection at eBay.com. Free shipping on many items. Carrier ZONECC0USI01-B Comfort Zone II User Interface. Brand: Carrier. $8.60 shipping. CARRIER COMFORT ZONE TEMPERATURE SENSOR ZONECCORRSSA NEW. CARRIER 33CS250-FS THERMOSTATS.

1. Each manual CARRIER VVT THERMOSTAT MANUAL (Complete). Topic on this With controls ranging from thermostats and zoning systems Page 2. High quality online resources for Carrier Comfort Zone 2 Installation Manual. 920415 comfort zone installation and start-up instructions, 920415 comfort zone Our Performance Comfortzone II 4 zone control.
2. The user can manu-ally activate unoccupied override. Set points can be adjusted during both occupied and unoccupied override modes. The occupied schedule controls when the zone is in oc-cupied or unoccupied mode. The schedule can be sent from a device over the network, or it can be programmed at the monitor thermostat or zone controller.
3. Back to the Comfort Zone II -B Equipment Controller. Select a location near the furnace or fan coil where wiring from the User Interface, each Remote Sensor or Smart Sensor, each damper actuator, and the equipment itself can come together easily. The Comfort Zone II -B System is approved for indoor use only.
4. View and Download Carrier COMFORT ZONE ZONEKIT4ZCAR installation and start-up instructions manual online. Carrier Air Conditioner User Manual. COMFORT ZONE ZONEKIT4ZCAR Controller pdf manual download.

Occupancy Schedule —

The occupancy schedule es-

tablishes the time periods when the monitor thermostat and
zone controller operate in the occupied or unoccupied mode.

The unoccupied/occupied schedule has individual 7-day

programming with 8 time periods. Unoccupied/occupied ON/
OFF times are entered on the minute. The start of an ON
time is the beginning of the occupied mode. The start of an
OFF time is the beginning of the unoccupied mode.
NOTE: If an ON time and an OFF time are set for the same
time, the monitor thermostat or zone controller operates in
unoccupied mode for that entire period.
NOTE: Access to the occupancy schedule by certain users
may be limited through the security level access function.

CONFIGURATION OF SCHEDULES — The unoccupied/
occupied program can be directly configured at the monitor
thermostat or zone controller. To configure the schedule, per-
form the following:
1. Press both upper or lower set point buttons at the same

time to enter into the program mode. The word ‘‘cat-
egory’’ and the number 1 will be displayed. See Fig. 2 for
programming mode button functions.

2. Press the left upper set point button. The word ‘‘cat-

egory’’ and the number 2 will be displayed. Category 2
contains the occupied/unoccupied schedules for the moni-
tor thermostat and zone controller.

3. The lower right set point button is the select button. Press

Carrier Comfort Zone Problems

the select button. The word ‘‘category’’ will change to
‘‘option’’ and the number 1 will be displayed. Category
2, options 1 through 8 are the 8 different occupancy time
periods. Option 1 is occupied period 1. Option 2 is oc-
cupied period 2. The options continue to option 8 which
is occupancy period 8.

4. The start time for option 1 will be shown. Each occupied

period (options 2.1 through 2.8) will have three different
screens associated with it — start time, stop time, and
active days. Use the left set point buttons to scroll through
the start time, stop time and active days for each option.
Press the select button (right lower set point button) to
modify the screen.

5. Configure the start time for category 2, option 1. When

the select button is pressed from the start time screen, the
hours number will flash. The hours are modified through
the left set point buttons. The AM/PM modifier will au-
tomatically switch when scrolling through the times. To
change the minutes, press the select button again. The min-
utes numbers will flash. Use the left set point buttons to
modify the minutes. Press select again to save the current
time and return to the options screen, or press escape (up-
per right set point button) to exit without saving changes.

6. Configure the stop time. Press the upper left set point but-

ton to advance to the stop time screen of category 2, op-
tion 1. Press the select button. The hours number will flash.
The hours are modified through the left set point buttons.
The AM/PM modifier will automatically switch when scroll-
ing through the times. To change the minutes, press the
select button again. The minutes numbers will flash. Use
the left set point buttons to modify the minutes. Press se-
lect again to save the current time and return to the op-
tions screen, or press escape to exit without saving changes.

7. Configure the active days. Press the upper left set point

button to advance to the active days screen of category 2,
option 1. Press the select button. The active days will be
shown and the first day, M (Monday) will be blinking.
Use the left set point buttons to turn the day ON or OFF.
Use the select button to scroll through the possible active
days. The programmable days are: M (Monday), T (Tues-
day), W (Wednesday), TH (Thursday), F (Friday), SA (Sat-
urday), SU (Sunday), and H (Holiday). Press select again
to save the current active days and return to the options
screen, or press escape to exit without saving changes.

8. Repeat this procedure for each time period until the cor-

rect schedule has been programmed.

9. When the schedule is complete, press escape to exit the

programming mode. If no buttons are pressed for 3 min-
utes while in programming mode, the display will auto-
matically revert back to its standard operating mode.

INCREASE
VALUE

DECREASE
VALUE

Carrier Comfort Zone Ii Installation Manual

PRESS BOTH TO ENTER
PROGRAMMING MODE

ESCAPE

SELECT

Fig. 2 — Programming Mode Buttons

3